Draw a Circle With a Nail and a String

1. one

   Cutting string that's one–2 inches (two.v–5.ane cm) longer than your desired radius. The circle y'all draw will have a diameter that's twice as long as the string you utilise, just y'all should cut information technology ane–2 inches (2.5–5.ane cm) longer than you want at first since you'll lose some of the length when you tie a loop at each end.^[1]

   • For instance, if you want your circumvolve to be iv inches (10 cm) across, so your desired radius would be 2 inches (5.1 cm) since the radius is equal to half of the bore. Therefore, you'd cut the slice of cord to be about three–4 inches (7.6–ten.2 cm) long so yous have extra cord on each cease to tie the loops with.

2. 

   two

   Tie a small loop at each end of the cord. You'll utilize i of the loops to adhere the cord to a pivot and the other loop to attach it to a pencil. The size of the loops doesn't need to be precise, but make sure they're big plenty to fit around a pencil and pivot but not so big that they use up a lot of the string that you lot cut.^[2]

   • When you're finished tying the loops, y'all tin measure the length of the string to determine what the exact radius of your circle will be. If the radius is besides short, y'all can always cut a longer slice of string and endeavour again.

   Advertisement

3. 

   3

   Place a slice of newspaper over some cardboard, styrofoam, or cork board. Any kind of cloth will work equally long every bit y'all're able to printing a pin into it. This base nether the paper will requite the pin something to stick into and assistance hold it in identify equally you use it to draw your circumvolve.

   • If you lot're drawing your circle onto a piece of thick material, like foam poster board or canvas, you lot can skip this step.
   • If y'all don't have anything to use as a base under your sheet of newspaper, you can endeavour holding the pivot in place on the paper with your fingers instead.

4. 

   4

   Push button a pivot through the paper where you desire the center of your circle to be. Any kind of push pin will work, although the shorter the pivot, the easier information technology will be to work with (since a alpine pin might stick up more and be less stable). Make certain information technology's non too shut to the border of the paper or else your circumvolve might go off the page when you describe information technology.^[3]

5. 

   five

   Loop one end of the string over the pin. Don't worry about tightening the loop. Every bit long every bit it'southward wrapped around the pin, you're all set.^[4]

   • Information technology doesn't matter what finish of the string you wrap around the pin. Only make sure the loop on the other finish is big enough to wrap around a pencil.

   Advertisement

1. 

   ane

   Loop the other cease of the string around the end of a pencil. Merely slide the tip of the pencil into the loop so the string is wrapped around the pencil. It's OK if the loop slides down the pencil. You'll be pulling it taut afterward on so information technology stays in place.^[v]

   • You don't have to use a pencil to draw your circle—you can use a pen, marker, colored pencil, or another drawing utensil every bit long as the loop fits around it.

2. 2

   Place the tip of the pencil on the paper so the cord is pulled taut. Pull the pencil away from the pin until the cord is completely taut. Then, place the tip of the pencil down. This is where the edge of your circle will exist.^[six]

   • Don't pull on the string too hard or you could pull the pin out.

3. 

   3

   Draw a circumvolve with the pencil, keeping the cord taut as you lot get. To draw your circumvolve, slowly move the pencil in a circular movement around the pin in the center, holding the pencil upward directly and not at an angle. Proceed gently pulling the pencil away from the pin in the center so that the string stays taut and your circle is even all the style around.^[7]

   • If you don't continue the cord taut, you won't stop upwards with a perfect circle. If your hand slips and y'all make a mistake, just erase what you've drawn and start over.

4. 4

   Remove the pin when you're finished cartoon your circle. If you desire to depict another circle, yous can push the pin into a different spot on the paper and repeat the process. Otherwise, fix the pivot and string bated for the side by side time y'all need to draw a perfect circle!

   Advertisement

Inquire a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

Thanks for submitting a tip for review!

Things You'll Need

• Newspaper
• Pencil
• String
• Scissors
• Pivot
• Cardboard, styrofoam, or cork board

Nigh This Article

Article Summary X

To depict a perfect circle using a pin, commencement by cut a piece of cord that's 1 to 2 inches longer than your desired radius and tying a small loop at each end. Then, place a slice of paper over some cardboard or styrofoam, push a pin through the eye of the paper, and loop 1 end of the string over the pivot. Next, loop the other terminate of the string effectually the stop of a pencil, and pull the pencil abroad from the pin and then the cord is completely taut. Finally, place the tip of the pencil on the paper and draw a circle, keeping the cord taut as you get. To learn more, including how to keep the pin in place if yous don't have whatever cardboard or styrofoam, go along reading.

Did this summary assist yous?

Cheers to all authors for creating a page that has been read xxx,117 times.

Did this article help yous?

adamdamil1958.blogspot.com

Source: https://www.wikihow.com/Draw-a-Perfect-Circle-Using-a-Pin

Share this post